MapPit & Pitron Installation for AutoCAD

In this page you can download a minimal version of MapPit + Pitron (1.8MB) or a full version that includes MapPit, Pitron, Contours and additional code systems (8.5MB).

You can also download here, a patch that will enable MapPit to work under the IntelliCAD98 (version 1.0d).

You can also download here, a 60 days demo of the software AreaFlex - Dynamically design lots and areas.

Note: If MapPit is already installed on your computer, You must backup the complete MapPit Directory before Installing the downloaded files.

Requirements:  

1.	Windows NT or Windows 95
2.	AutoCAD R14, AutoCAD Map R2, AutoCAD R3 or IntelliCAD 1.0d.
3.	About 15MB of free disk space.

   
Download:

Click the download button to download the Minimal version for MapPit & Pitron.
File name: Mapinst.exe
File size: 1.8MB

---

Click the download button to download the Full version for MapPit & Pitron.
File name: Map12inst.exe
File size: 8.5MB

---

---

To Download MapPit Manual in English click here

Installation:  

1.	Save the file in a temporary directory (C:\TEMP for example).
2.	Run the file you downloaded (Mapinst.exe or Map11inst.exe) in that directory (this should extract the installation files into a temporary directory and run the Setup.exe program).
3.	If setup was not started Run setup.exe from the temporary directory manually.
4.	Follow the instructions to install MapPit (use the serial number 1).  It is highly recommended to use the original installation  directory (C:\MAPPIT) as your target location.  This will facilitate the following installation steps.

The above steps will create MapPit folder in your computer.
Follow the steps 5 - 15 to load MapPit into AutoCAD and register it.
To install MapPit for IntelliCAD proceed by clicking here.

Load MapPit into AutoCAD:  

5.	Copy your AutoCAD 14 Icon.
6.	Rename the new Icon MapPit.
7.	Right click the MapPit Icon and choose Properties
8.	Click the Shortcut pane, and add in the Target right after the program name :      /p  MapPit
9.	Click OK button and double click the new MapPit Icon.  This should start  your AutoCAD and create a new profile named MapPit.
10.	From the AutoCAD menu choose [Tools][preferences].
11.	Choose the Files pane and press the small + mark labeled "support files search path"
12.	Use the Add button and the Move up button to add MapPit folder and MapPit\USR folders to the top of the search path. if you installed MapPit in C:\MAPPIT for example, add the folders :              C:\MAPPIT\USR              C:\MAPPIT
13.	Click Apply button and then Click the Profiles pane and choose your preferred Profile as current.
14.	Leave the AutoCAD and double click the MapPit icon again.  This time the MapPit application will be loaded into AutoCAD and you would see the registration dialog, in which you will be required to provide key2.
15.	Call us to get this key.  Notice: the keys will change each time you'll start the application, so you must call us while the registration dialog is activated.  Tel': 972-3-9603237 , Cell' 972-52-630211(Oded) or Cell' 972-52-929265 (Lior).
16.	Inside AutoCAD type the command "pitmenu". This will load MapPit menu and toolbar.

 
This installation process creates a separate Icon and separate profile for
MapPit, it assure minimal danger of damaging other applications settings.

For any assistance during the installation process, call us:
Tel': 972-3-9603237, Cell' 972-52-630211(Oded) or Cell' 972-52-929265 (Lior).

Load MapPit into IntelliCAD:
 

5.	Start IntelliCAD and choose from the IntelliCAD menu [Tools][Options]. This start the "Options" dialog-box.
6.	In the "Search path" edit box add the following: c:\mappit\icad;c:\mappit\usr;c:\mappit Then click [OK] button and start a new drawing (use the "new" command inside the IntelliCAD).
7.	In the new drawing, the MapPit application will be loaded and you would see the registration dialog, in which you will be required to provide key2.
8.	Call us to get this key.  Notice: the keys will change each time you'll start the application, so you must call us while the registration dialog is activated.  Tel': 972-3-9603237 , Cell' 972-52-630211(Oded) or Cell' 972-52-929265 (Lior).
9.	Inside IntelliCAD type the command "menuload". This will open the "MenuLoad" dialog-box.
10.	Click the [Import] button and choose the file pit_sub.mnu from the mappit\icad directory (usually c:\mappit\icad\pit_sub.mnu). make sure to chack the "Append to current menu" CheckBox ! This will load the MapPit, Pitron and Contours menus into the IntelliCAD.
11.	Inside IntelliCAD type the command "menuload" again. This will open the "MenuLoad" dialog-box.
12.	In the "Toolbars" pane, click the [Import] button and choose the same pit_sub.mnu file from the mappit\icad directory. make sure to chack the "Append to existing toolbars" CheckBox ! This will load the MapPit toolbar into the IntelliCAD.

Requirements:

AreaFlex works under AutoCAD R14 and up.  


Download:

Click the download button to download a 60 days demo of AreaFlex - Dynamically design lots and areas.
File name: AreaFlex.zip
File size: 1.91MB

---

---

see AreaFlex in action !!!

---

Installation:

1. After downloading the file AreaFlex.zip.
2. Extract this file into c:\temp directory.
3. Run the file : Setup.exe This will extract the directory c:\Flex into your Hard disk.
4. Run AutoCAD.
5. In AutoCAD 14 Go to -- Tools -- Preferences / In AutoCAD 2000 and up Go to -- Tools -- options (menu in AutoCAD)
6. go to files and open the first option : support file search path
7. Add line: c:\Flex
8. Mark this line and by clicking the button "Move Up" move this line to be the first line.
9. Click Applay and then O.K .
10. Close AutoCAD
11. Run AutoCAD
12. load the AreaFlex - In the command line bar write this line: (load "flex")
13. To load the Flex menu type in the command bar: flexmenu

Good Luck.

NOTE: under the Flex directory you can find a Tutorial drawing (Flex\Tutorial\FlexDemo1.dwg).
This is a good example for testing the AreaFlex utitlties.

---